For Consumer / IoT
Our technology and reliability
Long term peace of mind
Support your design
The R5463 Series are high voltage CMOS-based protection ICs for over-charge/discharge of two-cell Lithium-ion (Li+) / Lithium polymer, further include a short circuit protection circuit for preventing large external short circuit current and the protection circuits against the excess discharge-current and excess charge current.
Each of these ICs is composed of six voltage detectors, a reference unit, a delay circuit, a short circuit protector, an oscillator, a counter, and a logic circuit. When the over-charge voltage threshold or excess-charge current threshold crosses the each detector threshold from a low value to a high value, the output of COUT pin switches to “L” level after internal fixed delay time. To release over-charge detector after detecting over-charge, the detector can be reset and the output of COUT becomes "H" when a kind of load is connected to VDD after a charger is disconnected from the battery pack and the cell voltage becomes lower than over-charge detector threshold. In case that a charger is continuously connected to the battery pack, if the cell voltage becomes lower than the over-charge released voltage, over-charge state is also released.
The output of DOUT pin, the output of the over-discharge detector and the excess discharge-current detector, switches to “L” level after internally fixed delay time, when discharged voltage crosses the detector threshold from a high value to a value lower than VDET2. To release over-discharge detector, after detecting over-discharge voltage, connect a charger to the battery pack, and when the battery supply voltage becomes higher than the over-discharge detector threshold, the over-discharge detector is released and the voltage of DOUT pin becomes “H”. If the battery is discharged lower than maximum voltage for inhibition of charger, recharge current is not acceptable.
After detecting excess-discharge current or short current, when the load is disconnected, the excess discharged or short condition is released and DOUT becomes “H”.
After detecting over-discharge voltage, supply current will be kept extremely low by halting internal circuits' operation. When the output of COUT is “H”, if V- pin level is set at -1.6V, the delay time of over-charge and over-discharge detector can be shortened. Especially, the delay time of the over-charge detector can be reduced into approximately 1/60 and test time for protection circuit PCB can be reduced. The output type of COUT and DOUT is CMOS.
Specs & Datasheets
|Operating Input Voltage||1.5 V to 10.0 V (Maximum Rating: 12 V)|
|Charger Negative Input Voltage||-30 V|
|Number of Cells||2|
|Supply Current||Typ. 4.0 µA|
|Standby Current||Max. 0.1 µA|
|Overcharge Detection Voltage||3.65 V to 4.32 V (0.005 V Steps)|
|Overcharge Detection Voltage Accuracy||±20 mV|
|Overcharge Detection Delay Time||1.0 s|
|Overdischarge Detection Voltage||2.0 V to 3.2 V (0.1 V Steps)|
|Overdischarge Detection Voltage Accuracy||±1.0%|
|Overdischarge Detection Delay Time||128 ms|
|Discharge Overcurrent Detection Voltage||R5463K2xxxG: 0.05 V to 0.20 V (0.005 V Steps)
R5463K2xxxJ: 0.20 V to 0.40 V (0.005 V Steps)
|Discharge Overcurrent Detection Voltage Accuracy||R5463K2xxxG: ±10 mV
|Discharge Overcurrent Detection Delay Time||12 ms|
|Charge Overcurrent Detection Voltage||-0.20 V to -0.10 V (0.005 V Steps)|
|Charge Overcurrent Detection Voltage Accuracy||±20 mV|
|Charge Overcurrent Detection Delay Time||8 ms|
|Short Detection Voltage||1.0 V|
|Short Detection Delay Time||300 µs|
|Conditions for Overcharge Restoration||Voltage Release|
|Conditions for Overdischarge Restoration||Latch|
|0 V Charge||Unavailable|
|Output Delay Time Shortening||At COUT is “H”, if V- level is set at –1.6V, the Output Delay time of detect the over-charge and over-discharge can be reduced. (Delay Time for over-charge becomes about 1/60 of normal state.)|
|Temperature Protection||Reset||Alarm||Cell Balance||Cascadable||Open Wire Detection||Wakeup||Short-circuit Current Detection||Delay Time Shortening|
Quality & Packages
Refer to the datasheets for the details on the product.
The package file includes package dimensions, taping specifications, taping reels dimensions, power dissipations, and recommended land pattern.
Please contact us or our distributors for unpublished reliability information.
Sample / Buy
Please contact your local distributors for any sales-related inquiry such as price, stock, delivery, etc.
|Temperature Protection||Temperature Protection|
|Cell Balance||Cell Balance Function|
|Cascadable||Cascade Connect Function|
|Open Wire Detection||Open Wire Detect Function|
|Short-circuit Current Detection||Short-circuit Current Protection|
|Delay Time Shorting||Output Delay Time Short Function|
For more details, please refer to "Externally Configurable Protections and Their Advantages".