Skip to main content Skip to first level navigation
Skip to main content First level navigation Menu
Contact Us About Us ricoh.com
Breadcrumbs
Facebook (Open link in new window) YouTube (Open link in new window) LinkedIn (Open link in new window)
Main content
Main content

R5478 Series

1-Cell Li-ion Battery Protection IC

  • RoHS

The R5478 Series are high voltage CMOS-based protection ICs for over-charge/discharge of rechargeable one-cell Lithium-ion (Li+) / Lithium polymer excess load current, further include a short circuit protector for preventing large external short circuit current and Excess discharge-current.

Each of these ICs is composed of three voltage detectors, a reference unit, a delay circuit, a short circuit protector, an oscillator, a counter, and a logic circuit. When the over-charge voltage crosses the detector threshold from a low value to a high value, the output of COUT pin switches to low level after internal fixed delay time. The conditions to release over-charge detector are different by mask options. In terms of so called “Latch function” version, after detecting over-charge, the detector can be reset and the output of COUT becomes "H" when a kind of load is connected to VDD after a charger is disconnected from the battery pack, and the cell voltage becomes lower than over-charge detector threshold. If a charger is continue to be connected to the battery pack, even the cell voltage becomes lower than over-charge detector threshold, over-charge state is not released. On the other hand, in terms of so called, “Released by voltage level” version, after detecting over-charge, when the cell voltage reaches the released voltage from over-charge, the output of COUT becomes “H”.

The output of DOUT pin, the output of Over-discharge detector and Excess discharge-current detector, switches to “L” level after internally fixed delay time, when discharged voltage crosses the detector threshold from a high value to a value lower than VDET2.

The conditions to release over-discharge detector are also different by mask options. In terms of so called “Latch function” version, after detecting over-discharge voltage, connect a charger to the battery pack, and when the battery supply voltage becomes higher than over-discharge detector threshold, VD2 is released and the voltage of DOUT pin becomes "H" level. On the other hand, in terms of so called “Released by voltage level” version, in case that the charger is not connected, when the cell voltage becomes equal released voltage from over-discharge, over-discharge detector is released. In case that a charger is connected, and when the cell voltage becomes the released voltage from over-discharge, the over-discharge detector is released.

An excess discharge-current and short circuit state can be sensed and cut off through the built in excess current detector, VD3, with DOUT being enabled to low level. Once after detecting excess discharge-current or short circuit, the VD3 is released and DOUT level switches to high by detaching a battery pack from a load system.

After detecting over-discharge, supply current will be kept extremely low by halting internal circuits' operation.

When the output of COUT is “H”, if V- pin level is set at Vss-2V, the delay time of detector can be shortened.

Especially, the delay time of over-charge detector can be reduced into approximately 1/57. Therefore, testing time of protector circuit board can be reduced. Output type of COUT and DOUT are CMOS. 6-pin, SOT-23-6 is available.

Specs & Datasheets

   
Operating Input Voltage 1.5 V to 5.0 V (Maximum Rating: 12 V)
Number of Cells 1
Supply Current Typ. 3.0 µA
Standby Current R5478NxxxxC: Max. 0.1 µA
R5478NxxxxD/J/K: Typ. 1.2 µA
Overcharge Detection Voltage R5478NxxxxC/D: 4.2 V to 4.5 V (5 mV steps)
R5478NxxxxJ: 3.65V
R5478NxxxxK: 3.90V
Overcharge Detection Voltage Accuracy ±25 mV (Ta = 25°C)
±30 mV (-5°C ≤ Ta ≤ 55°C)
Overcharge Detection Delay Time 1s
Overdischarge Detection Voltage R5478NxxxxC/D/J: 2.1 V to 3.0 V (0.1 V steps)
R5478NxxxxK: 1.9 V to 3.0 V (0.1 V steps)
Overdischarge Detection Voltage Accuracy ±2.5%
Overdischarge Detection Delay Time 20ms
Discharge Overcurrent Detection Voltage 0.05 V to 0.20 V (5 mV steps)
Discharge Overcurrent Detection Voltage Accuracy ±15 mV
Discharge Overcurrent Detection Delay Time R5478NxxxxC: 12 ms
R5478NxxxxE: 6 ms
Short Detection Voltage 0.75 V
Short Detection Delay Time R5478NxxxxC: 300 µs
R5478NxxxxE: 200 µs
Conditions for Overcharge Restoration Latch / Voltage Release
Conditions for Overdischarge Restoration Latch / Voltage Release
Package SOT-23-6
0 V Charge Optional

Download Datasheet

Protections / Functions

Functional Description

Temperature Protection Reset Alarm Cell Balance Cascadable Open Wire Detection Wakeup Short-circuit Current Detection Delay Time Shortening
               

Technical Documents

Typical Application

Typical Application

Quality & Packages

Product Name Compatibility Package Marking Reliability
R5478Nxxxxx-TR-FF
  • gradeConsumerC
SOT-23-6 R5478N R5478N-FF

Refer to the datasheets for the details on the product.
The package file includes package dimensions, taping specifications, taping reels dimensions, power dissipations, and recommended land pattern.
Please contact us or our distributors for unpublished reliability information.

Sample / Buy

Functional Description

Temperature Protection Temperature Protection
Reset Reset Function
Alarm Alarm Function
Cell Balance Cell Balance Function
Cascadable Cascade Connect Function
Open Wire Detection Open Wire Detect Function
Wakeup Wakeup Function
Short-circuit Current Detection Short-circuit Current Protection
Delay Time Shorting Output Delay Time Short Function

For more details, please refer to "Externally Configurable Protections and Their Advantages".

Search for similar products under conditions below.

Category:Lithium-ion Battery Protection ICs

Features Battery Protection
Cell 1
Functions Short-circuit Current Detection