Skip to main content Skip to first level navigation
Skip to main content First level navigation Menu
お問い合わせ 企業情報 採用情報 株式会社リコー
Breadcrumbs
Facebook (Open link in new window) YouTube (Open link in new window) LinkedIn (Open link in new window)
Main content
Main content

R5478 シリーズ

1セル リチウムイオン電池用 保護IC

  • RoHS

The R5478 Series are high voltage CMOS-based protection ICs for over-charge/discharge of rechargeable one-cell Lithium-ion (Li+) / Lithium polymer excess load current, further include a short circuit protector for preventing large external short circuit current and Excess discharge-current.

Each of these ICs is composed of three voltage detectors, a reference unit, a delay circuit, a short circuit protector, an oscillator, a counter, and a logic circuit. When the over-charge voltage crosses the detector threshold from a low value to a high value, the output of COUT pin switches to low level after internal fixed delay time. The conditions to release over-charge detector are different by mask options. In terms of so called “Latch function” version, after detecting over-charge, the detector can be reset and the output of COUT becomes "H" when a kind of load is connected to VDD after a charger is disconnected from the battery pack, and the cell voltage becomes lower than over-charge detector threshold. If a charger is continue to be connected to the battery pack, even the cell voltage becomes lower than over-charge detector threshold, over-charge state is not released. On the other hand, in terms of so called, “Released by voltage level” version, after detecting over-charge, when the cell voltage reaches the released voltage from over-charge, the output of COUT becomes “H”.

The output of DOUT pin, the output of Over-discharge detector and Excess discharge-current detector, switches to “L” level after internally fixed delay time, when discharged voltage crosses the detector threshold from a high value to a value lower than VDET2.

The conditions to release over-discharge detector are also different by mask options. In terms of so called “Latch function” version, after detecting over-discharge voltage, connect a charger to the battery pack, and when the battery supply voltage becomes higher than over-discharge detector threshold, VD2 is released and the voltage of DOUT pin becomes "H" level. On the other hand, in terms of so called “Released by voltage level” version, in case that the charger is not connected, when the cell voltage becomes equal released voltage from over-discharge, over-discharge detector is released. In case that a charger is connected, and when the cell voltage becomes the released voltage from over-discharge, the over-discharge detector is released.

An excess discharge-current and short circuit state can be sensed and cut off through the built in excess current detector, VD3, with DOUT being enabled to low level. Once after detecting excess discharge-current or short circuit, the VD3 is released and DOUT level switches to high by detaching a battery pack from a load system.

After detecting over-discharge, supply current will be kept extremely low by halting internal circuits' operation.

When the output of COUT is “H”, if V- pin level is set at Vss-2V, the delay time of detector can be shortened.

Especially, the delay time of over-charge detector can be reduced into approximately 1/57. Therefore, testing time of protector circuit board can be reduced. Output type of COUT and DOUT are CMOS. 6-pin, SOT-23-6 is available.

仕様・データシート

   
動作入力電圧範囲 1.5 V to 5.0 V (Maximum Rating: 12 V)
セル数 1
消費電流 Typ. 3.0 µA
スタンバイ電流 R5478NxxxxC: Max. 0.1 µA
R5478NxxxxD/J/K: Typ. 1.2 µA
過充電 検出電圧範囲 R5478NxxxxC/D: 4.2 V ~ 4.5 V (5 mV steps)
R5478NxxxxJ: 3.65V
R5478NxxxxK: 3.90V
過充電 検出電圧精度 ±25 mV (Ta = 25°C)
±30 mV (-5°C ≤ Ta ≤ 55°C)
過充電 検出遅延時間 1s
過放電 検出電圧範囲 R5478NxxxxC/D/J: 2.1 V ~ 3.0 V (0.1 V steps)
R5478NxxxxK: 1.9 V ~ 3.0 V (0.1 V steps)
過放電 検出電圧精度 ±2.5%
過放電 検出遅延時間 20ms
放電過電流 検出電圧範囲 0.05 V to 0.20 V (5 mV steps)
放電過電流 検出電圧精度 ±15 mV
放電過電流 検出遅延時間 R5478NxxxxC: 12 ms
R5478NxxxxE: 6 ms
短絡 検出電圧範囲 0.75 V
短絡 検出遅延時間 R5478NxxxxC: 300 µs
R5478NxxxxE: 200 µs
過充電検出後の復帰条件 ラッチ/ 電圧復帰を選択可能
過放電検出後の復帰条件 ラッチ/ 電圧復帰を選択可能
パッケージ SOT-23-6
0V充電 選択可能

データシートダウンロード

保護回路/ 機能

機能説明

Temperature Protection Reset Alarm Cell Balance Cascadable Open Wire Detection Wakeup Short-circuit Current Detection Delay Time Shortening
               

技術資料

基本回路例

基本回路例

品質・パッケージ

製品名 対応 パッケージ情報 マーキング情報 信頼性データ
R5478Nxxxxx-TR-FF
  • gradeConsumerC
SOT-23-6 R5478N R5478N-FF

・製品詳細はデータシートをご参照ください
・パッケージ外形図、テーピング仕様、テーピングリール外形図、許容損失、基板パット推奨寸法 (ランドパターン)、などは各パッケージをご参照ください
・公開されていない信頼性情報については、販売店または当社までお問い合わせください

購入・サンプル

機能説明

Temperature Protection 温度保護
Reset リセット機能
Alarm アラーム機能
Cell Balance セルバランス機能
Cascadable カスケード接続機能
Open Wire Detection 断線検出機能
Wakeup ウェイクアップ機能
Short-circuit Current Detection 短絡保護機能
Delay Time Shorting 遅延時間短縮機能

各機能の詳細については、「外部保護機能とメリットについて」をご参照ください。

以下の仕様で類似品を検索します。

カテゴリ:リチウムイオン電池保護IC

特長  Battery Protection
セル 1
機能 Short-circuit Current Detection